Brother Hs-70a Manual
Are you doing 4 axis work or plain jane 2d stuff? I am a production shop, and as a result virtually ( all actually ) 2D. For that, all you really need is any 2D CAD program to draw your toolpath, and an old version of BobCAD to help filling in the G01/02/03-s. OTOH, Brother's codes are incredibly simple. I always set my 'tech' outside of the program, only modify some of the settings if and as I need it.
The 50A can use workoffsets, but the implementation - unfortunately - is a little retarded, so I pretty much resort to a G92 call instead. M86 is water/wire/electricity, call absolute G90 mode and then just let it rip on the toolpath. What is Espirit outputting that Brother doesn't like?
Brother Hs 70a Electrical Manual
Aug 09, 2017 I'm looking at picking up a Brother HS-70A for in-house tooling, fixturing and prototyping work. I know the Brother EDMs are orphans, but it. Brother Hs 70a Manual Brother hs 70a manual kawasolutions, browse and read brother hs 70a manual brother hs 70a manual what do you do to start reading brother.
We have two HS-70A machines and are using MasterCam X8. The post still doesn't do the tech settings correctly but they are simple to edit. The machines are great for the price and we still get support through Agie-Charmilles, for now. (edit) Sample programs: 1.
Small ID/OD in SS, one rough pass (XXXXXXXX, 42593, -HS70-) N10 G90 N12 G92 X0. N16 G10 U13030302 N18 G10 L9 N20 M26 N22 M22 N24 M86 N26 G41 G1 X.0585 Y.10132 N28 G3 X.05851 I.0585 J.10132 N30 X.0585 I.05851 J.10132 N32 M87 N34 M00 N36 G40 G0 X.0435 Y.07534 N38 M23 N40 G0 X.1795 Y.3109 N42 M22 N44 M86 N46 G42 G1 X.117 Y.20265 N48 G3 X.11703 Y.20263 I.117 J.20265 N50 M87 N52 M00 N54 M22 N56 M86 N58 X.117 Y.20265 I.11703 J.20263 N60 M87 N62 M00 N64 G40 G0 X.132 Y.22863 N66 M23 N68 M02 2. Carbide groove tool, one rough and two skims (XXXXXX, XXXXXX, -HS-70-) N005 G90 N010 G0 Z2. N015 G282 N020 G92 X0.
A couple other things we've found, and maybe someone here has better insight on them than I: 1. Do not put a program stop at a corner intersection. The machine will drop the offset and pick it back up on the following line. You CAN break either of those lines.015'.03' either side of the corner and stop there.
It's still a line-line intersection, but that's what works for us at least. You can stop at line-arc tangents and arc-arc tangents just fine, but not arc-arc, line-arc or line-line intersections, excepting the case that the lines are parallel apparently.
When doing a grease cycle, be VERY careful greasing the Z-axis lead screw. You cannot get them any more and they have a tendency to blow the seal out when you grease them.
We had to replace one, back when you could still get them, and have another rebuilt since. If you look in your manual on the 'Technology Code' page you will find that those tech call-outs are out of the machine library, so they are already in your machine. We have not bothered with saving a custom library. Any tech call-out that begins with 'U1' (ex. U13050109) is already in your machine library.
Archived from on February 10, 2011. Popcap games bejeweled. From the original on 22 September 2008.
Brother Hs 70a Electrical Manual
In the second example above, we are rough cutting a carbide blank with u/v taper r-to-l with a U13050107 rough setting. Stop to remove the scrap, switch to a U13050108 setting for the first skim l-to-r, and then take a second skim pass r-to-l again with a U13050109 tech.